how to empty a 20l dehumidifier correctly

Nov 09, 2026Leave a message

Hey everyone, it’s Mia from AB Dehumidifiers – and if you’ve ever stared at your 20L dehumidifier’s full water tank at 2am, panicking because you don’t want it overflowing all over your basement or workshop, this post is for you. I get it, 20L/h units (that’s the industrial-grade workhorses we supply) are built to pull massive amounts of moisture, but emptying them wrong can lead to spills, mold growth, or even break that expensive unit. Over the last 7 years working with these things – from printing workshops with sky-high humidity to wood drying facilities that need steady moisture control – I’ve seen so many people skip the basics and end up with headaches they don’t need. Let’s break down exactly how to empty a 20L dehumidifier correctly, no fancy tools or confusing steps required.

First, let’s get one thing straight: a 20L dehumidifier isn’t the tiny countertop unit you keep in your bathroom. These are heavy duty – 20 liters is roughly 5.28 gallons, so the tank alone can weigh 45+ lbs when full. I always tell new customers (like the printing workshops I worked with last month who bought our Printing Workshop Strong Humidification Air Dehumidifier) that rushing this step is how you spill water on electrical components, which is a surefire way to damage the unit. I learned this the hard way early on – my first month here, I tried to yank a full tank out of a test unit without turning it off, and it tripped the outlet’s GFCI. Embarrassing, but also a lesson that stuck: always start with safety.

Step 1: Prep before you touch the tank. This is non-negotiable for any 20L unit, especially the industrial ones we sell. First, turn the dehumidifier off at the main power button – don’t just unplug it (though you should do that too for good measure). Then, give it 2 minutes to pause its cycle before moving the tank. Why? Because the unit’s internal components are still shifting to stop pulling air when it’s off, and yanking the tank too soon can spill leftover water from the collection basin under the tank. Next, clear a spot nearby that’s waterproof – a towel, a bucket, even a rubber mat if you have it. This is where the tank’s going, and trust me, a little spill here is way better than spilling water on your shop floor or electrical cords. For units with a hose attachment (we offer that on most of our 20L models, by the way), make sure you know where that port is if you’re draining via hose, but we’ll cover that later.

Step 2: Remove the tank correctly, no brute force. The last thing you want is to crack the tank or yank it so hard you knock the whole dehumidifier over. Most 20L dehumidifiers have a latch that holds the tank in place – you pull it toward you slightly, then lift straight up. Don’t wiggle it side to side; that can dislodge the internal collection hose that feeds water into the tank, leading to a leak when you move it. When you lift it, hold the bottom of the tank with your other hand to support its weight – remember, that full 20L adds up fast, and dropping a 45lb tank on your foot is not a fun Tuesday. I always keep a small step stool by our test units too, just in case someone’s shorter or the dehumidifier is on a high shelf – don’t strain your back here.

Step 3: Empty and inspect the tank, don’t just dump it. Here’s where most people mess up. You don’t just carry the tank to a sink and pour it out – take 10 seconds to check what’s in there first. A lot of 20L units (especially ones with filters like our Active Carbon Filter Dehumidifier for basements) pick up dust, lint, or even mold spores from the air. If you just pour that down your sink, you can clog the drain, and if there’s mold in the tank, that’s going to grow if you don’t clean it. Instead, pour the water into a toilet or outdoor drain (never a kitchen sink with a garbage disposal, that’s a bad combo with lint) and then rinse the tank with warm, soapy water once a month, even if it looks clean. Wait, and check the float valve – that little plastic piece that tells the unit when the tank’s full. If it’s stuck, the dehumidifier will keep running even when the tank is empty, which wastes energy. To check it, after emptying, hold the tank upright and make sure the float moves up and down smoothly. If it’s sticky, wipe it with a dry cloth – no soap needed there, just make sure it moves freely.

Step 4: Choose your drain method (don’t rely on just the tank forever). Most of our 20L/h units come with the option to run a continuous drain hose, which is a game-changer for industrial use. If you’re running one in a printing workshop or wood drying space, you don’t need to empty the tank at all – just attach the hose to the drain port on the back of the unit and run it to a floor drain or sump pump. This is what our customers who bought the Wood Drying Adsorption Rotor Desiccant Dehumidifier swear by – they run it 24/7, and the hose lets them forget about emptying it for weeks. But if you do use the tank method, make sure you reinsert it correctly. Align the notches on the tank with the slots in the unit, push it straight in until you hear a click, and then turn the unit back on. If it beeps at you, the tank isn’t seated right – don’t force it, pull it out and try again. That click is important because it tells the unit the tank is in place, so it will start dehumidifying again right away.

Wait, hold on – I want to touch on a common mistake people make with 20L units specifically. Because these are designed for high-capacity use, some people try to empty the tank more often, but no – if the tank is only half full, you’re wasting energy by running the unit on a short cycle. On the flip side, if you let it go way past full, you’re risking water overflowing into the unit’s internal parts, which can lead to mold in the ductwork or even a broken compressor. We’ve had a few customers reach out last year saying their 20L unit stopped working, and 9 times out of 10, it was because they didn’t empty the tank for 2+ weeks, and the water leaked into the electrical components. It’s a quick fix if you catch it early, but avoid that hassle by sticking to a schedule.

Now, if you’re using a 20L dehumidifier in a commercial or industrial space, like a warehouse or manufacturing floor, you might want to look into our Commercial Composite Rotor Dehumidifier Supplier line – we build models with larger tanks and easier drain access for those high-humidity areas. But even with those, the same rules apply: prep, remove the tank carefully, inspect, reinsert. No exceptions.

Best Selling Industrial DehumidifierAdsorption Industrial Desiccant Dehumidifier For Wood Drying

Another thing I get asked all the time: can I use a bucket instead of the drain hose? Totally, but make sure the bucket is bigger than 20L. If you just put a small bucket under the tank, it’s going to spill when the tank empties. And never leave the unit unattended with the bucket – especially if you’re running it overnight. I’ve had a customer who did that for a week, and the bucket tipped over while he was at work, leading to a small flood in his storage area. So if you use a bucket, check it every 6 hours or so, or set an alarm on your phone.

Let’s also talk about when to clean the tank, not just empty it. Even if the water looks crystal clear, every time you empty it, you should wipe the inside with a mild bleach solution (1 part bleach to 10 parts water) once a month, especially if you’re using it in a damp space. This kills any bacteria or mold spores that get in from the air, which is important because if the tank has mold, that mold will blow back into your space through the dehumidifier’s air intake. Our Active Carbon Filter Dehumidifiers help reduce some of that dust, but cleaning the tank is still a must.

Wait, I should mention a specific tip for if you’re transporting the dehumidifier after emptying. If you need to move the unit to a different space, don’t just pick it up by the top – empty the tank, then tilt it slightly to pour out any leftover water in the internal collection basin. If you move it straight, that water can spill into the compressor, which is expensive to fix. I learned this when we had to move 10 units to a trade show a couple years ago – two of them had water in the compressor because we didn’t drain the basins first. Now we have a step-by-step check for every unit before moving, and it’s saved us a ton of headaches.

Now, let’s wrap this up with a quick recap, so you don’t forget anything: 1. Turn off and wait 2 minutes before touching the tank. 2. Support the tank from the bottom, lift straight up (no wiggling). 3. Empty the water, rinse the tank, check the float valve. 4. Reinsert until you hear a click, turn the unit back on. 5. For continuous use, use a drain hose – no more tank emptying needed. 6. Clean the tank monthly with a mild solution to prevent mold.

If you’re looking for a new 20L dehumidifier, or have questions about which one is right for your space – whether it’s a printing workshop, wood drying, or industrial/commercial use – feel free to reach out to our team to talk through your needs. We’re here to help you keep your space dry, no spills or headaches required.

REFERENCES

  1. Residential Dehumidifier Maintenance Guidelines, Air Conditioning Contractors of America, 2022
  2. Industrial Dehumidifier Water Collection System Best Practices, International Dehumidification Manufacturers Association, 2023
  3. Mold Prevention in Dehumidifier Tanks, Environmental Protection Agency, 2021
  4. Commercial Dehumidifier Operation Manual, AB Dehumidifiers, 2024